334 30 H T D3 Q p1 V1 30 20 M5 6 O 30 48 55 55 G 3 /8” 30 20 M5 G1/ 2” 65 6 36 59 65 O K2 F1 U Z M U R S Y I W F X K1 G1 G B E C3 A 14,5 K3 SIN-HL 85 + 100 SIN-HL 125, 150, 175 SMW-AUTOBLOK A B C3 D3 E F F1 G G1 H I K1 K2 K3 M O Q h6 (6x60°) g6 H7 J6 H8 SIN-HL 85 33093809 85 80 120 11 140 M24 M16 x1.5 LH 32 30 x 10 192 5 25 18 18 75 G3/8” 77 SIN-HL 100 33093810 100 80 120 11 140 M24 M16x1.5 LH 32 30 x 10 192 5 25 18 18 75 G3/8” 77 SIN-HL 125 33093812 125 95 145 13 166 M30 M16x1.5 LH 40 38 x 12 231 5 31 18 24 93 G1/2” 97 SIN-HL 150 33093815 150 95 170 13 192 M36 M16x1.5 LH 50 48 x 12 237 5 37 18 28 97 G1/2” 97 SIN-HL 175 33093817 175 125 195 13 217 M36 M16x1.5 LH 50 48 x 12 259 5 37 18 28 97 G1/2” 97 SMW-AUTOBLOK R S T U V1W X Y Z p1 SIN-HL 85 149.5 47 95 32 10 40 10 62 27 23 49 70 19 1.5 7000 11 0.016 SIN-HL 100 149.5 47 95 32 10 45 10 62 27 23 70 70 28 1.5 7000 11 0.016 SIN-HL 125 181 70 121 40 12 55 10 75 27 37 110 70 44 1.5 6000 18 0.045 SIN-HL 150 183 70 121 40 12 55 10 75 27 41 157 70 62 1.5 6000 23 0.092 SIN-HL 175 205 72 143 52 12 55 10 75 27 41 220 70 88 1.5 5000 30 0.15 2 s SIN-HL Closed center rotating hydraulic cylinder ■ High-low clamping ■ Up to 70 bar ■ Central bore for media supply ■ Stroke control via proximity switch or LPS 4.0 For easily deformed components SMW-AUTOBLOK offers ”high-low“ clamping. The gripping force of the chuck can be reduced from a large amount of gripping force used in roughing, to a smaller amount of gripping force for a finishing cut. „High-low“ clamping for thin-walled components Application/customer benefits • Actuation of power chucks used for high-low clamping of thin-walled components in combination with SMW-AUTOBLOK chucks type KNCS-N, KNCS-NB, KNCS-NBX, HFKN, IEP or TS • Closed or partial open center mounting applications Technical features • Symmetric piston areas for high-low clamping • Pressure range 8 - 70 bar • Horizontal or vertical installation • Safety valves and excess pressure relief valve • Central bore for coolant, oil or air with thread for rotary union • Mounting from the rear side with bolts • Stroke control via proximity switch or LPS 4.0 • A 10 μm filter in pressure line is requested. Use oil HM32 ISO 3448 Standard equipment Ordering example Closed center hydraulic cylinder with Closed center cylinder stroke control and mounting bolts SIN-HL 125 Id. No. 33093812 (without proximity switches) with rotary union (optional) * Total at 30 bar and 50°C. Dimensions and technical data The combination between the SIN-HL cylinder and a SMW-AUTOBLOK ”high-low“ suitable chuck allows a monitored reduction in the gripping force. The component remains clamped in the chuck safely, however, the stress of the component can be released. The result are round components with a minimum of deformation. The ”high-low“ cycle is programmable and is finished completely within 2-4 sec. For additional information please ask our engineers. Roughing operation high gripping force Finishing operation low gripping force Roughing Chuck gripping force Timing Finish machining Without „high-low” clamping Result Subject to technical changes. For more detailed information please ask our customer service. Id. No. Type mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm inch mm Piston area Max. pressure Draw (at 40 bar) Oil leakage* Max. speed Weight Moment of inertia Type min. mm mm mm mm mm mm mm mm mm mm cm2 bar kN dm3/min. r.p.m. kg kg·m² With „high-low” clamping BIS Specials Website: www.bisspecials.com Email: info@bisspecials.com Tel: (0031) 0313 482566 Website: www.bisspecials.com Email: info@bisspecials.com Tel: (0031) 0313 482566
RkJQdWJsaXNoZXIy NDg1ODE=